← All posts

22 de novembro de 2026

How to Turn a Performance Video Into a Slowed-Down Practice Track

Learn a part by ear from a concert or recital video. Four steps in one browser tab give you a short, slowed, loud enough MP3 that keeps the original key.

Someone filmed the performance on their phone, and somewhere in that seven-minute video is the 32 seconds you need to learn: a guitar break, an alto line, the bridge your band keeps fumbling. At full speed the notes go past before you can catch them. Scrubbing back to 2:10 in a video player forty times an evening gets old fast, and the phone's speaker makes it quieter than the room it was recorded in.

What you actually want is a small audio file that contains only that passage, plays at three quarters of the speed without dropping into a lower key, and is loud enough to hear over your own instrument. If you want to slow down a song from a video to learn it, that file is the goal, and no single tool makes it.

It takes four, used in one browser tab. Each result goes straight into the next tool, and you download once, at the end.

The chain at a glance

  1. Pull the audio out of the video so the audio tools can work on it
  2. Cut it down to the passage you're learning, with a few seconds of lead-in
  3. Slow it to 0.75× with the pitch kept where it was
  4. Raise the volume now that only the music is left

Step 1: Get the sound out of the video

The speed tool works on audio files, not video, so the first job is to get from the MP4 (or the MOV your iPhone saved) to an MP3. Drop the video into the converter. Your file stays in the browser, which matters when the clip is a 400 MB recording of someone else's kid's recital.

Under Quality (bitrate), choose High · 320 kbps rather than the 192 kbps default. Every tool after this one re-encodes the audio when it saves, so a cleaner starting point leaves more detail for the later steps to work with. Leave sample rate and channels on Same as source. Stereo matters here: the guitar is often panned to one side, and on headphones that separation helps you pick it out.

When the conversion finishes, don't download. Under Send to another tool, the trimmer isn't in the two suggestions, so open Other compatible tools and choose Trim audio.

MP4 to MP3 →

Step 2: Keep only the passage, plus a breath before it

Write down the timestamps now, from the video you already watched. If the solo runs from 2:10 to 2:42, type 2:05 into Start and 2:44 into End. The extra five seconds at the front give you time to put the phone down and get your hands on the instrument before the hard part arrives.

The waveform helps you check. Applause and talking show up as dense blocks, and you can usually see where the band comes back in. Use Preview selection to confirm you haven't clipped the first note. Turn on Fade out so the loop ends softly instead of chopping a chord in half, which is jarring on the fortieth repeat. Leave Fade in off if the passage starts on a strong downbeat you want to hear clearly.

Click Trim audio. On the result screen, the speed tool is again behind Other compatible tools; pick Change audio speed there.

Trim audio →

Step 3: Slow it down without changing the key

Click the 0.75× preset. Check that Keep pitch is on (it is by default). With it on, the tool stretches the timing and leaves the notes where they were, so you can play along in the same key as the recording. With it off, slowing down also drops the pitch, roughly like playing a record at the wrong speed, and everything you learn would be in the wrong key.

Hit Play preview before you commit. The preview changes in real time as you move the slider, so you can find the speed where the passage is just barely playable. That is a better target than whatever sounds comfortable. Start around 0.75× for fast runs. If you can already play it at that speed, go back up to 0.85× or 0.9× with the slider. Very slow settings, near 0.5× and below, start to sound smeared, which is fine for picking out individual notes and less fine for feeling the groove.

The tool tells you the new length before it runs. Your 39-second excerpt becomes 52 seconds at 0.75×.

Click Change speed. This time the next tool is right there: Boost audio volume is one of the suggested next steps.

Change audio speed →

Step 4: Make it loud enough to play over

Phone recordings from the audience are quiet, and the music is quieter still once you're playing along. The boost tool shows the file's peak as soon as it loads, which tells you how much headroom you have.

The default is +6 dB. Try +9 dB or +12 dB with the presets, then press and hold Compare to switch between the original and the boosted version. Keep Auto-limit to 0 dB on. If a loud cymbal hit would push the level past the top, the limiter holds it down instead of letting it crackle. If you switch the limiter off and push too far, the tool warns you that the output will clip before you've saved anything.

Click Boost & download. This is the only file you save.

Boost audio volume →

Why this order

Trim before you slow down. Your timestamps come from the original video. Once the audio is at 0.75×, every moment moves later: the solo that started at 2:10 now starts at 2:53, and the one that ended at 2:42 ends at 3:36. Cut first and you can use the numbers you already wrote down. Slowing a 39-second excerpt is also much faster than slowing a seven-minute concert.

Trim before you boost, too. This is the one that catches people. A recital or gig recording almost always includes applause, and a room full of people clapping close to the phone is often the loudest thing in the file, louder than the music. The boost tool sets its headroom by the loudest peak. If you boost the whole recording, the applause decides how far you can go, and the passage you care about stays quiet. Once the clapping is gone, the peak reading drops and you can add several more decibels to the music itself.

Boost last. Changing the speed doesn't make the audio louder or quieter, so in principle you could boost before step 3. Doing it last means the version you hold Compare on is exactly the file you'll practice with, at the speed you'll hear it. You judge the volume once, on the final result.

Extract first, even though it feels like extra work. You could trim the video instead, but the audio trimmer shows you a waveform, takes typed timestamps, and adds fades, which is what you need for a clean loop. And from step 2 on, every tool is working on a small audio file instead of hundreds of megabytes of video.

What you end up with

A single MP3 of about 50 seconds: your passage, a short lead-in, a soft fade at the end, three quarters of the original speed, in the original key, and loud enough to hear over an acoustic guitar. Set your phone's player to repeat it, or drop it into the band's group chat so everyone practices the same part at the same tempo. When it gets easy, run it through the speed tool again at 0.9×. The whole chain takes a few minutes, and most of that is listening.

Ready to start? Open MP4 to MP3 →